Runlevel/Default: Unterschied zwischen den Versionen

Version vom 28. Januar 2025, 13:15 Uhr

Runlevel/Default - Beschreibung

Beschreibung

Seit Debian 9/10 wird systemd werden systemd/targets anstelle von run-levels benutzt

Die Datei /etc/inittab wird von systemd nicht mehr verwendet, um die Ausführungsebenen zu ändern

Anwendung

Change Default runlevel

The Default runlevel can be set either by using the systemctl command or making a symbolic link of runlevel targets file to the default target file

Method 1

Let’s check the current run level by using the following command

sudo systemctl get-default
graphical.target

Before changing the default runlevel, check out the available targets

sudo systemctl list-units --type=target
 UNIT LOAD ACTIVE SUB DESCRIPTION
 basic.target loaded active active Basic System
 cryptsetup.target loaded active active Encrypted Volumes
 getty.target loaded active active Login Prompts
 graphical.target loaded active active Graphical Interface
 local-fs-pre.target loaded active active Local File Systems (Pre)
 local-fs.target loaded active active Local File Systems
 multi-user.target loaded active active Multi-User System
 network-online.target loaded active active Network is Online
 network.target loaded active active Network
 nss-user-lookup.target loaded active active User and Group Name Lookups
 paths.target loaded active active Paths
 remote-fs.target loaded active active Remote File Systems
 slices.target loaded active active Slices
 sockets.target loaded active active Sockets
 sound.target loaded active active Sound Card
 swap.target loaded active active Swap
 sysinit.target loaded active active System Initialization
 time-sync.target loaded active active System Time Synchronized
 timers.target loaded active active Timers
 
 LOAD = Reflects whether the unit definition was properly loaded
 ACTIVE = The high-level unit activation state, i.e. generalization of SUB
 SUB = The low-level unit activation state, values depend on unit type

Issue the following command to change the default runlevel to runlevel 3 (nothing but a multi-user.target)

sudo systemctl set-default multi-user.target

Confirm the default runlevel

sudo systemctl get-default
 multi-user.target

Reboot and check it out

sudo reboot

Method 2

In the previous method, we made the runlevel 3 as the default runlevel

You can also confirm that using the following command

sudo systemctl get-default
 multi-user.target

For a demo, issue the following command to make runlevel 5 as the default runlevel

sudo ln -sf /lib/systemd/system/runlevel5.target /etc/systemd/system/default.target

OR

sudo ln -sf /lib/systemd/system/graphical.target /etc/systemd/system/default.target

Again check the current level

Now the default runlevel is the graphical mode(runlevel 5)

sudo systemctl get-default
 graphical.target

Reboot the machine and check it out

sudo reboot

Problembehebung

Konfiguration

Dateien

Datei	Beschreibung
/proc/sys
/etc/sysctl.conf

Anhang

Siehe auch

Runlevel/Default

Dokumentation

Man-Page

Info-Pages

Links

Projekt

Weblinks

@@ Zeile 83: / Zeile 83: @@
 * Now the default runlevel is the graphical mode(runlevel 5)
-<syntaxhighlight lang="bash" highlight="1" line>
+<syntaxhighlight lang="bash" highlight="1" line="">
- # systemctl get-default
+sudo systemctl get-default
   graphical.target
 </syntaxhighlight>
 Reboot the machine and check it out
-<syntaxhighlight lang="bash" highlight="1" line>
+<syntaxhighlight lang="bash" highlight="1" line="">
- # reboot
+sudo reboot
 </syntaxhighlight>
@@ Zeile 106: / Zeile 106: @@
 |}
 <noinclude>
 == Anhang ==
 === Siehe auch ===