Limits.conf

limits.conf - configuration file for the pam_limits module

Beschreibung

• The pam_limits.so module applies ulimit limits, nice priority and number of simultaneous login sessions limit to user login sessions.

/etc/security/limits.conf

This description of the configuration file syntax applies to the /etc/security/limits.conf file

/etc/security/limits.d

and *.conf files in the /etc/security/limits.d directory.

Anwendung

These are some example lines which might be specified in /etc/security/limits.conf.

*               soft    core            0
root            hard    core            100000
*               hard    nofile          512
@student        hard    nproc           20
@faculty        soft    nproc           20
@faculty        hard    nproc           50
ftp             hard    nproc           0
@student        -       maxlogins       4
@student        -       nonewprivs      1
:123            hard    cpu             5000
@500:           soft    cpu             10000
600:700         hard    locks           10

Syntax

The syntax of the lines is as follows:

<domain> <type> <item> <value>

The fields listed above should be filled as follows:

<domain>

username
groupname	with @group syntax. This should not be confused with netgroups.
wildcard *	for default entry.
wildcard %	for maxlogins limit only, can also be used with %group syntax. If the % wildcard is used alone it is identical to using * with maxsyslogins limit. With a group specified after % it limits the total number of logins of all users that are member of the group.
uid range	specified as <min_uid>:<max_uid>. If min_uid is omitted, the match is exact for the max_uid. If max_uid is omitted, all uids greater than or equal min_uid match.
gid range	specified as @<min_gid>:<max_gid>. If min_gid is omitted, the match is exact for the max_gid. If max_gid is omitted, all gids greater than or equal min_gid match. For the exact match all groups including the user's supplementary groups are examined. For the range matches only the user's primary group is examined.
gid	specified as %:<gid> applicable to maxlogins limit only. It limits the total number of logins of all users that are member of the group with the specified gid.

NOTE: group and wildcard limits are not applied to the root user. To set a limit for the root user, this field must contain the literal username root.

<type>

hard	for enforcing hard resource limits. These limits are set by the superuser and enforced by the Kernel. The user cannot raise his requirement of system resources above such values.
soft	for enforcing soft resource limits. These limits are ones that the user can move up or down within the permitted range by any pre-existing hard limits. The values specified with this token can be thought of as default values, for normal system usage.
-	for enforcing both soft and hard resource limits together.

Note, if you specify a type of '-' but neglect to supply the item and value fields then the module will never enforce any limits on the specified user/group etc. .

<item>

core	limits the core file size (KB)
data	maximum data size (KB)
fsize	maximum filesize (KB)
memlock	maximum locked-in-memory address space (KB)
nofile	maximum number of open file descriptors
rss	maximum resident set size (KB) (Ignored in Linux 2.4.30 and higher)
stack	maximum stack size (KB)
cpu	maximum CPU time (minutes)
nproc	maximum number of processes
as	address space limit (KB)
maxlogins	maximum number of logins for this user (this limit does not apply to user with uid=0)
maxsyslogins	maximum number of all logins on system; user is not allowed to log-in if total number of all user logins is greater than specified number (this limit does not apply to user with uid=0)
nonewprivs	value of 0 or 1; if set to 1 disables acquiring new privileges by invoking prctl(PR_SET_NO_NEW_PRIVS)
priority	the priority to run user process with (negative values boost process priority)
locks	maximum locked files (Linux 2.4 and higher)
sigpending	maximum number of pending signals (Linux 2.6 and higher)
msgqueue	maximum memory used by POSIX message queues (bytes) (Linux 2.6 and higher)
nice	maximum nice priority allowed to raise to (Linux 2.6.12 and higher) values: [-20,19]
rtprio	maximum realtime priority allowed for non-privileged processes (Linux 2.6.12 and higher)
chroot	the directory to chroot the user to

• All items support the values -1, unlimited or infinity indicating no limit, except for priority, nice, and nonewprivs. If nofile is to be set to one of these values, it will be set to the contents of /proc/sys/fs/nr_open instead (see setrlimit(3)).
• If a hard limit or soft limit of a resource is set to a valid value, but outside of the supported range of the local system, the system may reject the new limit or unexpected behavior may occur. If the control value required is used, the module will reject the login if a limit could not be set.
• In general, individual limits have priority over group limits, so if you impose no limits for admin group, but one of the members in this group have a limits line, the user will have its limits set according to this line.
• Also, please note that all limit settings are set per login. They are not global, nor are they permanent; existing only for the duration of the session. One exception is the maxlogin option, this one is system wide. But there is a race, concurrent logins at the same time will not always be detect as such but only counted as one.
• In the limits configuration file, the '#' character introduces a comment - after which the rest of the line is ignored.
• The pam_limits module does report configuration problems found in its configuration file and errors via syslog(3).

Siehe auch

1. pam_limits(8)
2. pam.d(5)
3. pam(7)
4. getrlimit(2)
5. getrlimit(3p)

Testfragen

Testfrage 1

Antwort1

Testfrage 2

Antwort2

Testfrage 3

Antwort3

Testfrage 4

Antwort4

Testfrage 5

Antwort5